SAN DIEGO COUNTY AIR POLLUTION CONTROL DISTRICT

RULE 260.113a - TESTING AND PROCEDURES
(Rev. Effect. 3/14/89)

(a) Except as provided in Rule 260.8(b) compliance with the standard prescribed in Rule 260.112a shall be determined as follows or in accordance with an equivalent procedure as provided in Rule 260.114a.
 

1.  The owner or operator of each storage vessel to which this subpart applies which has an external floating roof shall meet the following requirements:

(i) Determine the gap areas and maximum gap widths between the primary seal and the tank wall and between the secondary seal and the tank wall according to the following frequency: (Rev. Effective 3/14/89)

(A) For primary seals, gap measurements shall be performed within 60 days of the initial fill with petroleum liquid and at least once every five years thereafter. All primary seal inspections or gap measurements which require the removal or dislodging of the secondary seal shall be accomplished as rapidly as possible and the secondary seal shall be replaced as soon as possible.

(B) For secondary seals, gap measurements shall be preformed within 60 days of the initial fill with petroleum liquid and at least once every year thereafter.

(C) If any storage vessel is out of service for a period of one-year or more, subsequent refilling with petroleum liquid shall be considered initial fill for the purposes of Subsections (a)(1)(i)(A) and (a)(1)(i)(B) of this rule.

(D) Keep records of each gap measurement at the plant for a period of at least 2 years following the date of measurement. Each record shall identify the vessel on which the measurement was performed and shall contain the date of the seal gap measurement, the raw data obtained in the measurement process required by Subsection (a)(1)(ii) of this rule and the calculation required by Subsection (a)(1)(iii) of this rule.

(E) If either the seal gap calculated in accord with Subsection (a)(1)(iii) of this rule or the measured maximum seal gap exceeds the limitations specified by Rule 260.112a of this subpart, a report shall be furnished to the Control Officer within 60 days of the date of measurements.

The report shall identify the vessel and list each reason why the vessel did not meet the specifications of Rule 260.112a. The report shall also describe the actions necessary to bring the storage vessel into compliance with the specifications of Rule 260.112a.

(ii) Determine gap widths in the primary and secondary seals individually by the following procedures:

(A) Measure seal gaps, if any, at one or more floating roof levels when the roof is floating off the roof leg supports.

(B) Measure seal gaps around the entire circumference of the tank in each place where a 1/8 in. diameter uniform probe passes freely (without forcing or binding against seal) between the seal and the tank wall and measure the circumferential distance of each such location.

(C) The total surface area of each gap described in Subsection (a)(1) (ii)(B ) of this rule shall be determined by using probes of various widths to accurately measure the actual distance from the tank wall to the seal and multiplying each such width by its respective circumferential distance.

(iii) Add the gap surface area of each gap location for the primary seal and the secondary seal individually. Divide the sum for each seal by the nominal diameter of the tank and compare each ratio to the appropriate ratio in the standard in Rule 260.112a (a)(1)(i) and Rule 260.112a(a)(1)(ii).

(iv) Provide the Control Officer 30 days prior notice of the gap measurement to afford the Control Officer the opportunity to have an observer present.

1. The owner or operator of each storage vessel to which this subpart applies which has a vapor recovery and return or disposal system shall provide the following information to the Control Officer on or before the date on which construction of the storage vessel commences:

(i) Emission data, if available, for a similar vapor recovery and return or disposal system used on the same type of storage vessel, which can be used to determine the efficiency of the system. A complete description of the emission measurement method used must be included.

(ii) The manufacturer's design specifications and estimated emission reduction capability of the system.

(iii) The operation and maintenance plan for the system.

(iv) Any other information which will be useful to the Control Officer in evaluating the effectiveness of the system in reducing VOC emissions.