SACAQMD RULE 902 ASBESTOS
LAST REVISED 06/01/95                              





                              RULE 902 ASBESTOS
                                Adopted 6-2-75
                    (Amended 5-31-89, 1-14-92, 6-1-95)
                                   INDEX

100 GENERAL
    101  PURPOSE
    110  EXEMPTIONS

200 DEFINITIONS
    201  ACTIVE WASTE DISPOSAL SITE
    202  ADEQUATELY WETTED
    203  ASBESTOS
    204  ASBESTOS-CONTAINING MATERIAL
    205  ASBESTOS-CONTAINING WASTE MATERIAL
    206  ASBESTOS MILL
    207  ASBESTOS TAILING
    208  CATEGORY I NONFRIABLE ASBESTOS-CONTAINING MATERIAL
    209  CATEGORY II NONFRIABLE ASBESTOS-CONTAINING MATERIAL
    210  COMMERCIAL ASBESTOS
    211  COMPLETION DATE
    212  CONTROL DEVICE ASBESTOS WASTE
    213  CONVERSION OPERATION
    214  DEMOLITION
    215  ELEMENT
    216  EMERGENCY RENOVATION
    217  FABRICATING
    218  FRIABLE ASBESTOS-CONTAINING MATERIAL
    219  GLOVE BAG TECHNIQUE
    220  HEPA FILTER
    221  INACTIVE WASTE DISPOSAL SITE
    222  LEAK-TIGHT
    223  MANUFACTURING
    224  ORDERED DEMOLITION  
    225  OUTSIDE AIR
    226  OWNER OR OPERATOR OF A DEMOLITION OR RENOVATION 
    227  PARTICULATE ASBESTOS MATERIAL
    228  PLANNED RENOVATION
    229  REMOVING
    230  REGULATED ASBESTOS-CONTAINING MATERIAL (RACM)
    231  RENOVATION
    232  RESILIENT FLOOR COVERING
    233  ROADWAYS
    234  SECURED
    235  SET UP
    236  START DATE
    237  STATIONARY STRUCTURE
    238  STRIPPING
    239  STRUCTURAL MEMBER
    240  VISIBLE EMISSIONS
    241  WASTE GENERATOR
    242  WASTE SHIPMENT RECORD 
    243  WORKING DAY
    244  WRECKING

300 STANDARDS
    301  DEMOLITION AND RENOVATION
    302  WASTE DISPOSAL
    303  MANUFACTURING
    304  FABRICATING
    305  SPRAYING
    306  INSULATING
    307  ROADWAYS
    308  ASBESTOS MILLS
    309  WASTE DISPOSAL FOR ASBESTOS MILLS
    310  WASTE DISPOSAL SITES
    311  EXCEPTIONS TO VISIBLE EMISSION STANDARD

400 ADMINISTRATIVE REQUIREMENTS 
    401  REPORTING

500 MONITORING AND RECORDS 
    501  TESTING PROCEDURES
    502  RECORD KEEPING



100 GENERAL

    101  PURPOSE: To limit the emission of asbestos to the atmosphere and
         require an appropriate waste disposal procedure.

    110  EXEMPTIONS:  
         110.10   This rule shall not apply to:
               a. renovations or demolitions of single family residential
                  dwellings comprised of four or fewer residential dwelling
                  units, except where the intended use is for residential
                  property with five or more units, or commercial or
                  industrial property, or 
               b. renovations where the combined amount of RACM is less
                  than 260 lineal feet, or less than 160 square feet, or
                  less than 35 cubic feet.
         110.2 Section 300 of this rule shall not apply to demolitions where
               the combined amount of RACM is less than 260 lineal feet, or
               less than 160 square feet, or less than 35 cubic feet.
    
200 DEFINITIONS:  For the purpose of this rule only, the following definitions
                  shall apply:

    201  ACTIVE WASTE DISPOSAL SITE: Any disposal site other than an inactive
         site.

    202  ADEQUATELY WETTED: Sufficiently mixed or penetrated with liquid to
         prevent the release of asbestos-containing material. The absence of
         dust, debris or particles is not sufficient evidence of being
         adequately wetted.

    203  ASBESTOS: Actinolite, amosite, anthophyllite, chrysotile, crocidolite
         and tremolite.

    204  ASBESTOS-CONTAINING MATERIAL: Asbestos or any material containing
         more than 1% asbestos, as determined by the method specified in
         Section 501.2.

    205  ASBESTOS-CONTAINING WASTE MATERIAL:
         205.1 Any waste which contains commercial asbestos and is generated
               by a source subject to the provisions of this rule, including
               filters from control devices, asbestos mill tailings, friable
               asbestos waste material, and bags or containers that
               previously contained commercial asbestos. 
         205.2 Any waste from demolition and renovation including but not
               limited to RACM, waste, disposable equipment and clothing,
               and other materials contaminated with asbestos.

    206  ASBESTOS MILL: Any facility engaged in the conversion or any
         intermediate step in the conversion of asbestos ore into commercial
         asbestos. Outside storage of asbestos materials is not considered a
         part of such facility.

    207  ASBESTOS TAILING: Any solid waste product of asbestos mining or
         milling operation which contains asbestos.

    208  CATEGORY I NONFRIABLE ASBESTOS-CONTAINING MATERIAL: Asbestos-
         containing packings, gaskets, resilient floor coverings, and asphalt
         roofing products.

    209  CATEGORY II NONFRIABLE ASBESTOS-CONTAINING MATERIAL: Asbestos-
         containing material, excluding Category I nonfriable asbestos-
         containing material, that, when dry, and in its present form, cannot
         be crumbled, pulverized, or reduced to powder by hand pressure.

    210  COMMERCIAL ASBESTOS: Any variety of asbestos which is produced by
         extracting asbestos from asbestos ore.

    211  COMPLETION DATE: The date when all asbestos removing or stripping is
         finished and all asbestos-containing waste has been properly removed
         from the project.

    212  CONTROL DEVICE ASBESTOS WASTE: Any asbestos-containing waste material
         that is collected in a pollution control device.

    213  CONVERSION OPERATION: A process by which asbestos material and/or
         asbestos-containing waste material is converted to nonasbestos
         (asbestos-free) material.

    214  DEMOLITION: The wrecking, taking out, or burning of any
         load-supporting structural member of any stationary structure or any
         related removing or stripping of RACM.

    215  ELEMENT: Any boiler, pipe, furnace, duct, tank, reactor, turbine, or
         structural member.

    216  EMERGENCY RENOVATION: A renovation that results from a sudden,
         unexpected event, applies to the abatement of the immediate hazard
         and, that if not immediately attended to:
            216.1 presents a safety or public health hazard, 
            216.2 is necessary to protect equipment from damage,
            216.3 or is necessary to avoid imposing an unreasonable
                  financial burden,
            216.4 and is not a planned renovation.
         Ultimate approval of the use of this provision is left to the
         discretion of the Air Pollution Control Officer or the EPA
         Administrator. Operations necessitated by non-routine failures of
         equipment are included.

    217  FABRICATING: Any processing of a manufactured product containing
         commercial asbestos, with the exception of processing at temporary
         sites for the construction or restoration of building, structures,
         facilities or installations.

    218  FRIABLE ASBESTOS-CONTAINING MATERIAL: Asbestos-containing material
         that can be crumbled, pulverized, or reduced to powder, when dry, by
         hand pressure.
         
    219  GLOVE BAG TECHNIQUE: A method of stripping or removing RACM in which
         the material is totally isolated inside a leaktight bag and then
         manually removed using gloves which are an integral part of the bag.

    220  HEPA FILTER: A high efficiency particulate air filter capable of
         filtering 0.3 micron particles with 99.97 percent efficiency.

    221  INACTIVE WASTE DISPOSAL SITE: Any disposal site or portion thereof,
         where additional asbestos-containing waste material will not be
         deposited and where the surface is not disturbed by vehicular
         traffic.

    222  LEAK-TIGHT: Any method of containerization that prevents solids,
         liquids, or particles from escaping or spilling out.

    223  MANUFACTURING: The combining of commercial asbestos, or in the case
         of woven friction products the combining of textiles containing
         commercial asbestos, with any other material(s), including commercial
         asbestos, and the processing of this combination into a product as
         specified in Section 303.

    224  ORDERED DEMOLITION: The demolition of a stationary structure pursuant
         to an order of an authorized representative of a state or local
         governmental agency, issued because that structure is structurally
         unsound and in danger of imminent collapse.

    225  OUTSIDE AIR: The air outside buildings and structures.

    226  OWNER OR OPERATOR OF A DEMOLITION OR RENOVATION: Any person who owns,
         leases, operates, controls or supervises the stationary structure
         being demolished or renovated, or any person who owns, leases,
         operates, controls or supervises demolition or renovation, or both.

    227  PARTICULATE ASBESTOS MATERIAL: Finely divided particles of asbestos
         material.

    228  PLANNED RENOVATION: A renovation, in which the amount of RACM that
         will be removed or stripped within a given period of time can be
         predicted. Operations that are individually non-scheduled are
         included, provided a number of such operations can be predicted to
         occur during a given period of time based on operating experience.

    229  REMOVING: The taking out, cutting, dislodging, drilling, or similarly
         disturbing of RACM covering or coating of any element from any
         stationary structure, or portion thereof.

    230  (RACM):REGULATED ASBESTOS-CONTAINING MATERIAL: 
         230.1 Friable asbestos-containing material, or,
         230.2 Category I nonfriable asbestos-containing material that has
               or will become friable, or subjected to sanding, drilling,
               grinding, cutting, or abrading, or,
         230.3 Category II nonfriable asbestos-containing material that has
               a high probability of becoming crumbled, pulverized, or
               reduced to powder by the forces expected to act on the
               material in the course of demolition or renovation.

    231  RENOVATION: The removing or stripping of RACM used to cover or coat
         any element of a stationary structure or portion thereof. 

    232  RESILIENT FLOOR COVERING: Asbestos-containing material comprised of
         floor tile, including asphalt or vinyl floor tile, or sheet vinyl
         floor covering.

    233  ROADWAYS: Surfaces on which motor vehicles travel including, but not
         limited to, highways, roads, streets, parking areas, and driveways.

    234  SECURED: Free from danger, loss or effects of the environment.

    235  SET UP: Preparation of a structure for stripping or removing of RACM,
         including but not limited to placement of physical barriers,
         installation of local exhaust ventilation and collection systems,
         removal of structural components for the primary purpose of gaining
         access to RACM, and any activity which would break up the RACM. 

    236  START DATE: The date disturbance, active removal or stripping of any
         regulated asbestos-containing material commences.

    237  STATIONARY STRUCTURE: Any immobile building, facility or
         installation. This includes a group of residential buildings with
         four or fewer dwelling units, owned, managed by or under control or
         authority of the same person, persons or agency, and which is part
         of a commercial or public project .

    238  STRIPPING: The taking off, cutting, drilling, dislodging, or similar
         disturbing of RACM covering or coating on any element of a stationary
         structure, or portion thereof.

    239  STRUCTURAL MEMBER: Any load supporting member, such as beams and
         load-supporting walls; or any non-load-supporting member, such as
         ceilings and non-load-supporting walls.

    240  VISIBLE EMISSIONS: Any emissions or evidence of emissions, including
         but not limited to dust, debris, particles, or fibers, which are
         visually detectable without the aid of instruments and which are
         asbestos-containing material. This does not include condensed,
         uncombined water vapor.

    241  WASTE GENERATOR: Any owner or operator of a source subject to this
         rule whose act or process produces asbestos-containing waste
         material.

    242  WASTE SHIPMENT RECORD: The shipping document required, by the Air
         Pollution Control Officer, to be originated and signed by the waste
         generator, used to track and substantiate the disposition of
         asbestos-containing waste material.

    243  WORKING DAY: Any day Monday through Friday including holidays that
         fall on any of the days Monday through Friday.

    244  WRECKING: The act of damaging and reducing to ruinous state.

300 STANDARDS

    301  DEMOLITION AND RENOVATION: Any owner or operator of a demolition or
         renovation, subject to this rule, shall use the following procedures
         to prevent emissions of particulate asbestos material to outside air:
         301.1 SURVEYS: Except for ordered demolitions, prior to
               commencement of any demolition or renovation, the owner or
               operator shall thoroughly survey the affected stationary
               structure or portion thereof, for the presence of asbestos-
               containing material, including Category I and Category II
               nonfriable asbestos-containing material.
               a. The survey shall be performed by a person who has taken
                  an EPA approved Building Inspector course and conforms
                  to the procedure outlined in the course.
               b. When a building owner or operator engages the services
                  of a person to perform asbestos consulting or site
                  surveillance activities, the building owner or operator
                  shall contract with a person who is certified by the
                  Division of Occupational Safety and Health pursuant to
                  regulations required by subdivision (b) of Section 9021.5
                  of the Labor Code.
               c. The survey shall include one of the following:
                  i.  The results of sampling and laboratory analysis of
                      the asbestos content of all suspect asbestos-
                      containing materials, or
                  ii. The reason the material is believed to contain
                      asbestos by the person performing the survey.
               d. When a stationary structure is demolished under an
                  ordered demolition, the survey must be done after
                  demolition but prior to handling, loading or removal of
                  any demolition debris.
         301.2 ACTIVITY PRIOR TO REMOVAL: RACM shall be removed from any
                  stationary structure subject to this rule before any
                  activity occurs that would disturb the RACM or that would
                  preclude access to such materials for subsequent removal.
                  Removal of RACM which is encased in concrete or other
                  similar structural materials is not required prior to
                  demolition, but such material shall be adequately wetted
                  whenever exposed during demolition.
         301.3 EXEMPTIONS TO THE WETTING REQUIREMENT: RACM shall be
               adequately wetted during stripping or removing except as
               provided below: 
               a. FREEZING TEMPERATURES: The wetting requirements of this
                  section are suspended when the temperature at the point
                  of wetting is below 0 degrees C (32 degrees F). When RACM
                  is not wetted due to freezing temperatures, such material
                  on elements shall, to the maximum extent possible, be
                  removed as units or in sections prior to wrecking. In no
                  case shall the requirements of Sections 301.7.b, 301.7.c,
                  301.7.d, or 301.7.e be suspended due to freezing
                  temperatures.
               b. During periods when wetting operations are suspended due
                  to freezing temperatures, the owner or operator must
                  record the temperature in the work area at the beginning,
                  middle and end of each workday and keep daily temperature
                  records available for inspection by the Air Pollution
                  Control Officer during normal business hours at the
                  demolition or renovation site. The owner or operator
                  shall retain the temperature records for at least 2
                  years.
               c. EQUIPMENT DAMAGE: For renovations, isolation by physical
                  barrier, local exhaust ventilation and collection systems
                  may be used, instead of wetting to prevent emissions of
                  particulate asbestos materials to outside air when damage
                  to equipment resulting from the wetting would be
                  unavoidable. Upon request and supply of adequate
                  information, the Air Pollution Control Officer will
                  determine whether damage to equipment resulting from
                  wetting to comply with the provisions of this paragraph
                  would be unavoidable. Such local exhaust ventilation
                  systems shall maintain the air in the isolated area at
                  a pressure differential of a least minus 0.02 inches of
                  water with respect to the area outside the barrier and
                  shall filter the air from the isolated area with a HEPA
                  filter or equivalent, prior to exhausting to the outside
                  air. There shall be no visible emissions to the outside
                  air from such local exhaust ventilation and collection
                  systems.
         301.4 PHYSICAL BARRIERS: RACM being stripped or removed, shall be
               isolated by physical barriers from the outside air to the
               extent feasible as determined by the Air Pollution Control
               Officer, except as provided in Section 301.9. Such barriers
               shall:
               a. VIEWING PORT: Include transparent viewing ports which
                  allow observation, to the extent possible, of all
                  stripping and removing of RACM from outside the barrier.
                  Viewing ports must be accessible and have an unobstructed
                  view of the interior at all times from the set up date
                  to completion date.
               b. PRESSURE DIFFERENTIAL: Whenever the outside air is in
                  contact with the air in any portion of the isolated area,
                  utilize a local exhaust ventilation system, to the extent
                  feasible as determined by the Air Pollution Control
                  Officer, during stripping and removing, which shall
                  maintain the air in the isolated area at a pressure
                  differential of at least minus 0.02 inches of water with
                  respect to the area outside the barrier. Any such local
                  exhaust ventilation system shall filter the air from the
                  isolated area with a HEPA filter or equivalent, prior to
                  exhausting to the outside air.
         301.5 POSTING: All points of entry to a demolition or renovation,
               subject to Section 301, shall display signs with the
               following legend which is easily read by the public. The
               warning signs shall, at a minimum, conform to the
               requirements of 20" x 14" unright format signs specified by
               OSHA and this paragraph.
                                  
                                  
                                  CAUTION
                           ASBESTOS DUST HAZARD
                           AVOID BREATHING DUST

         301.6 REMOVAL IN SECTIONS: RACM may be removed as units or in
               sections provided the RACM exposed during cutting or
               disjointing is adequately wetted during the cutting or
               disjointing operation. Such units shall not be dropped or
               thrown to the ground, but shall be carefully lowered to
               ground level.
         301.7 ORDERED DEMOLITION: The owner or operator of an ordered
               demolition shall adequately wet the portion of the structure
               being demolished that contains RACM during the wrecking
               operation.
         301.8 MAINTENANCE OF REMOVED RACM - WASTE HANDLING: All RACM that
               has been removed or stripped shall be:
               a. Kept adequately wetted at all times, and
               b. Transported to the ground via dust-tight chutes if it has
                  been removed or stripped more than 50 feet above the
                  ground, except material removed as units or in sections,
                  and
               c. Stored in transparent, leaktight containers, and
               d. Labeled with the name of the waste generator and the
                  location at which the waste was generated, and
               e. Stored in a secured and locked area until collected for
                  transport to a waste disposal site operated in accordance
                  with the provisions of Section 310 of this rule.
         301.9 GLOVEBAG: The requirement for physical barriers and local
               exhaust ventilation systems shall not apply when the
               stripping or removal is accomplished exclusively with a glove
               bag technique.
         301.10   ON-SITE REPRESENTATIVE: No RACM shall be stripped or removed,
                  unless at least one on-site representative, such as a foreman
                  or management-level person or other authorized
                  representative, certifies that he or she is familiar with the
                  provisions of this rule, as it pertains to demolition and
                  renovation, and the means of compliance, and is present
                  during all stripping and removing of RACM. The required
                  training shall, at a minimum, include Asbestos Hazard
                  Emergency Response Act (AHERA) certification, which meets the
                  U.S. Environmental Protection Agency, 40CFR, Part 763,
                  Subpart E. Certification documents shall be on the project
                  site and presented to the Air Pollution Control Officer upon
                  request.
               a. Applicability;
               b. Notifications;
               c. Material identification;
               d. Control procedures for removals,including:
                  1.  Wetting;
                  2.  Local exhaust ventilation;
                  3.  Negative pressure enclosures;
                  4.  Glove bag procedures; and
                  5.  HEPA filters.
               e. Waste disposal work practices;
               f. Reporting and record keeping requirements.
         301.11   INTENTIONAL BURNING: If demolition is accomplished by
                  intentional burning, all RACM, including Category I and
                  Category II nonfriable asbestos-containing material, shall
                  be removed in accordance with Section 301, before burning.
         301.12   RACM DISCOVERED AFTER DEMOLITION: If RACM is discovered after
                  demolition begins and cannot be safely removed, all of the
                  asbestos contaminated debris shall be treated as asbestos-
                  containing waste material 
         301.13   EMERGENCY RENOVATION: An emergency renovation shall be
                  approved by the Air Pollution Control Officer or the EPA
                  Administrator prior to the initiation of work and shall apply
                  to only the abatement of the immediate hazard.

    302  WASTE DISPOSAL FOR DEMOLITION, RENOVATION, MANUFACTURING,
         FABRICATING, AND SPRAYING OPERATIONS: The owner or operator of any
         source subject to the provisions of Sections 301, 303, 304, or 305
         of this rule shall meet the following standards:
         302.1 There shall be no visible emissions to the outside air,
               except as provided in Section 311 of this rule, during the
               collection, processing (including incineration), packaging,
               transportation, or disposition of any asbestos-containing
               waste material which is generated by such source;
         302.2 All asbestos-containing waste material shall be deposited at
               waste disposal sites which are operated in accordance with
               the provisions of Section 310, and shall be labeled with the
               name of the waste generator and the location at which the
               waste was generated.
         302.3 An owner or operator may elect to use any of the disposal
               methods specified under Subsections a., b. and c. of this
               Section or any alternative disposal method which has received
               prior approval by the Air Pollution Control Officer.
               a. Treatment of asbestos-containing waste material with
                  water:
                  1.  Control device asbestos waste shall be thoroughly
                      mixed with water into a slurry and other
                      asbestos-containing waste material shall be
                      adequately wetted, and,
                  2.  After wetting, all asbestos-containing waste
                      material shall be sealed into leak-tight containers
                      while wet, and such containers shall be deposited at
                      waste disposal sites which are operated in
                      accordance with the provisions of Section 310. The
                      containers shall be labeled with a warning label
                      that states:

                                  CAUTION
                             CONTAINS ASBESTOS
                     AVOID OPENING OR BREAKING CONTAINER
                    BREATHING ASBESTOS IS HAZARDOUS TO YOUR HEALTH

                  Alternatively, warning labels specified by the
                  Occupational Safety and Health Administration may be
                  used. All waste shall be labeled with the name of the
                  waste generator and the location at which the waste was
                  generated.
               b. Processing of asbestos-containing waste material into
                  nonfriable forms:
                  1.  All asbestos-containing waste material shall be
                      formed into nonfriable pellets or other shapes and
                      deposited at waste disposal sites which are operated
                      in accordance with the provisions of Section 310,
                      and shall be labeled with the name of the waste
                      generator and the location at which the waste was
                      generated.
                  2.  For the purposes of Section 302, the term
                      asbestos-containing waste material, as applied to
                      demolition and renovation operations covered by
                      Section 301 of this rule, includes RACM and control
                      device asbestos waste.
               c. Conversion of RACM and asbestos-containing waste material
                  into nonasbestos (asbestos-free) material:
                  1.  Each owner or operator of a conversion operation
                      shall comply with Sections 401.6 and 501.1 of this
                      rule.
                  2.  Discharge no visible emissions to the outside air
                      from any part of the operation or use methods
                      specified in Section 311 to remove particulate
                      asbestos material before venting to the outside air.
         302.4 For demolitions where the RACM is not removed prior to
               demolition pursuant to Section 301.8, the asbestos-containing
               waste material shall be kept adequately wetted at all times
               after demolition, during handling and loading and shall be
               sealed in leak-tight containers for transport to a disposal
               site.
         302.5 All asbestos-containing waste material shall be properly
               disposed of in compliance with this rule within 90 days of
               the date generated.
         302.6 All vehicles used to transport asbestos-containing waste
               material, shall be marked, during the loading and unloading
               of waste. The signs shall be visible and shall:
               a. Be displayed in such a manner that a person can easily
                  read the legend;
               b. Be 20 inch by 14 inch upright format signs;
               c. Display the following legend in a style and size at equal
                  to one inch Sans Serif, Gothic, or Block. Spacing between
                  any two lines shall be at least equal to the height of
                  the upper of the two lines. The signs shall state:

                                  DANGER
                           ASBESTOS DUST HAZARD
                      CANCER AND LUNG DISEASE HAZARD
                         AUTHORIZED PERSONNEL ONLY

         302.7 All asbestos-containing waste material transported off the
               facility site, shall meet all of the following requirements:
               a. Maintain a waste shipment record, including the following
                  information:
                  1.  The name, address, and telephone number of the waste
                      generator;
                  2.  The name and address of the local Air Quality
                      Management District in which the waste was
                      generated;
                  3.  The approximate amount of waste in cubic yards;
                  4.  The name and telephone number of the disposal site
                      operator;
                  5.  The name and physical location of the disposal site;
                  6.  The date transported;
                  7.  The name, address, and telephone number of the
                      transporter(s);
                  8.  A certification that the contents of this
                      consignment are fully and accurately described by
                      proper shipping name and are classified, packed,
                      marked, and labeled, and are in all respects in
                      proper condition for transport by highway;
               b. Provide a copy of the waste shipment record referenced
                  in Section 302.7.a to the disposal site owner or operator
                  at the same time the asbestos-containing waste material
                  is delivered to the disposal site.
               c. Contact the transporter and/or the owner or operator of
                  the disposal site to determine the status of the waste
                  shipment, if the waste shipment record referenced in
                  Section 302.7.a, signed by the owner or operator of the
                  designated disposal site, is not received by the waste
                  generator within 35 days of the date the waste was
                  accepted by the initial transporter. 
               d. Provide a written report to the Air Pollution Control
                  Officer if a copy of the waste shipment record referenced
                  in Section 302.7.a, signed by the owner or operator of
                  the disposal site, is not received by the waste generator
                  within 45 days of the date the waste was accepted by the
                  initial transporter. The following information shall be
                  included:
                  1.  A copy of the waste shipment record referenced in
                      Section 302.7.a for which a confirmation of delivery
                      was not received; and
                  2.  A letter signed by the waste generator explaining
                      the efforts taken to locate the asbestos waste
                      shipment and the results of those efforts;
               e. Retain a copy of all waste shipment records including a
                  copy of the waste shipment record, referenced in Section
                  302.7.a., signed by the owner or operator of the
                  designated waste disposal site, for at least 2 years and
                  provide a copy to the Air Pollution Control Officer upon
                  request.

    303  MANUFACTURING: No person shall discharge visible emissions to the
         outside air through an exhaust stack, or from any building or
         structure in which the following materials are manufactured or
         directly from the manufacture of these materials if they are
         manufactured outside of buildings or structures. This provision shall
         not apply to air cleaning pursuant to Section 311. 
         303.1 Cloth, cord, wicks, tubing tape, twine, rope, thread, yarn,
               roving, lap or other textile materials.
         303.2 Cement products.
         303.3 Fireproofing and insulating materials.
         303.4 Friction products.
         303.5 Paper, millboard, and felt.
         303.6 Floor tile.
         303.7 Paints, coatings, caulks, adhesives and sealants.
         303.8 Plastics and rubber materials.
         303.9 Chlorine.
         303.10   Shotgun shells.
         303.11   Asphalt concrete.
         303.12   Rocket motors, engines and components.

    304  FABRICATING: There shall be no visible emissions to the outside air,
         except as provided in Section 311 from any of the following
         operations if they use commercial asbestos or from any building or
         structure in which such operations are conducted.
         304.1 The fabrication of cement building products.
         304.2 The fabrication of friction products, except those operations
               that primarily install asbestos friction materials on motor
               vehicles.
         304.3 The fabrication of cement or silicate board for ventilation
               hoods, ovens, electrical panels, laboratory furniture,
               bulkheads, partitions and ceilings for marine construction,
               and flow control devices for the molten metal industry.

    305  SPRAYING: There shall be no visible emissions to the outside air from
         the spray-on application of asbestos-containing materials used to
         insulate or fireproof equipment and machinery, except as provided in
         Section 311. Spray-on materials used to insulate or fireproof
         buildings, structures, pipes, and conduits shall contain less than
         1 percent asbestos as determined according to the method specified
         in Section 501.2.

    306  INSULATING: Molded insulating materials which are friable and
         wet-applied insulating materials which are friable after drying, and
         which are installed or reinstalled after May 31, 1989, shall contain
         no commercial asbestos. The provisions of this paragraph do not apply
         to insulating materials which are spray applied. Such materials are
         regulated under Section 305.

    307  ROADWAYS: The surfacing of roadways with asbestos-containing waste
         material is prohibited except for temporary roadways on an area of
         asbestos ore deposits. The deposition of asbestos tailings on
         roadways covered with snow or ice is considered "surfacing".

    308  ASBESTOS MILLS: No person shall discharge visible emissions to the
         outside air from any asbestos mill except when air-cleaning is
         elected as provided in Section 311.

    309  WASTE DISPOSAL FOR ASBESTOS MILLS: The owner or operator of any
         source covered under the provisions of Section 308 of this rule shall
         meet the following standards.
         309.1 There shall be no visible emissions to the outside air,
               except as provided in Section 309.3 of this rule, during the
               collection, processing, packaging, transporting or
               disposition of any asbestos-containing waste material which
               is generated by such source;
         309.2 All asbestos-containing waste material shall be deposited at
               waste disposal sites which are operated in accordance with
               the provisions of Section 310; and
         309.3 Rather than meet the requirements of Section 309.1 of this
               rule, an owner or operator may elect to meet the following
               requirements specified in Subsections a., b. and c.:
               a. There shall be no visible emissions to the outside air
                  from transfer of control device asbestos waste to the
                  tailings conveyor, except as provided in Section 311.
                  Such waste shall be subsequently processed either as
                  specified in Section 309.3.b or as specified in Section
                  302.3 of this rule.
               b. All asbestos-containing waste material shall be
                  adequately mixed, with a wetting agent recommended by the
                  manufacturer of the agent to effectively wet dust and
                  tailings, prior to disposition at a waste disposal site.
                  Such agent shall be used as recommended for the
                  particular dust by the manufacturer of the agent. There
                  shall be no discharge of visible emissions to the outside
                  air from the wetting operation except as specified in
                  Section 311. Wetting may be suspended when the ambient
                  temperature at the waste disposal site is less than 0
                  degrees C (32 degrees F). The ambient air temperature
                  shall be determined by an appropriate measurement method
                  with an accuracy of plus, minus 1o C (plus, minus 2oF)
                  and recorded at least at hourly intervals during the
                  period that the operation of the wetting system is
                  suspended. Records of such temperature measurements shall
                  be retained at the source for a minimum of two years and
                  made available for inspection by the Air Pollution
                  Control Officer.
               c. Use an alternative emission control and waste treatment
                  method that has received prior written approval of the
                  Air Pollution Control Officer. A written application
                  shall be submitted to the Air Pollution Control Officer
                  demonstrating that the following requirements have been
                  met:
                  1.  The asbestos emissions shall be controlled by the
                      alternative method in a manner equivalent to
                      currently required methods; and
                  2.  The alternative method shall be suitable for the
                      intended application; and
                  3.  The alternative method shall not violate other
                      applicable rules, regulations or laws;
         309.4 When waste is transported by vehicle to a disposal site, all
               the requirements set forth in Section 302.6 shall be met.
         309.5.   For off-site disposal, all the requirements set forth in
                  Section 302.7 shall be met.
    
    310  WASTE DISPOSAL SITES: The owner of any inactive waste disposal site,
         which was operated by sources covered under Sections 301, 303, or 306
         and where asbestos-containing waste material produced by such sources
         was deposited, and an owner of an active waste disposal site which
         accepted waste from sources covered under Sections 301, 303, 304,
         305, 308, and 502.3 shall meet the following standards:
         310.1 There shall be no visible emissions to the outside air from
               any waste disposal site subject to this paragraph, except as
               provided in Section 310.5 or Section 310.6 of this rule;
         310.2 Warning signs shall be displayed at all entrances, and along
               the property line of the site or along the perimeter of the
               sections of the site where asbestos-containing waste material
               was deposited, at intervals of 330 feet or less, except as
               specified in Section 310.4 of this rule. Signs shall be
               posted in such a manner and location that a person may easily
               read the legend. The warning signs required by this paragraph
               shall conform to the requirements of 20" x 14" upright format
               signs specified by OSHA and this paragraph. The signs shall
               display the following legend in the lower panel, with letter
               sizes and styles of a visibility at least equal to those
               specified in this Section 310.2. Spacing between lines shall
               be at least equal to the height of the upper of the two
               lines.

                       ASBESTOS WASTE DISPOSAL SITE
                            DO NOT CREATE DUST
              BREATHING ASBESTOS IS HAZARDOUS TO YOUR HEALTH

                                 Notation
                      1" Sans Serif, Gothic or Block
                     3/4" Sans Serif, Gothic or Block
                              14 Point Gothic

         310.3 The perimeter of the site shall be fenced in a manner
               adequate to deter access by the general public, except as
               specified in Section 310.4 of this rule.
         310.4 Warning signs and fencing are not required where the
               requirements of Sections 310.5.a or 310.5.b of this rule are
               met, or where a natural barrier adequately deters access by
               the general public. Upon request and supply of appropriate
               information, the Air Pollution Control Officer will determine
               whether a fence or a natural barrier adequately deters access
               to the general public.
         310.5 Rather than meet the requirement of Section 310.1 an owner
               or operator of an inactive waste disposal site where
               asbestos-containing waste material has been deposited, may
               elect to meet the requirements of this paragraph, or may use
               an alternative control method for emissions from inactive
               waste disposal sites which has received prior approval by the
               Air Pollution Control Officer.
               a. The asbestos-containing waste material shall be covered
                  with at least six inches of compacted
                  nonasbestos-containing material, and a cover of
                  vegetation shall be grown and maintained on the area
                  adequate to prevent exposure of the asbestos-containing
                  waste material; or
               b. The asbestos-containing waste material shall be covered
                  with at least two feet of compacted
                  nonasbestos-containing material and maintained to prevent
                  exposure of the asbestos-containing waste; or 
               c. For inactive waste disposal sites for asbestos tailings,
                  a resinous or petroleum-based dust suppression agent
                  which affectively binds dust and controls wind erosion
                  shall be applied. Such agent shall be used as recommended
                  for the particular asbestos tailings by the dust
                  suppression agent manufacturer. Other equally effective
                  dust suppression agents may be used upon prior approval
                  by the Air Pollution Control Officer. For purposes of
                  this paragraph, waste crankcase oil is not considered a
                  dust suppression agent.
         310.6 Rather than meet the requirement of Section 310.1 of this
               rule, an owner or operator of an active waste disposal site
               may elect to meet the requirements of Sections 310.6.a
               310.6.b of this rule, or may use an alternative control
               method for emissions from active waste disposal sites which
               has received prior approval by the Air Pollution Control
               Officer.
               a. At the end of each operating day, or at least once every
                  24-hour period while the site is in continuous operation,
                  the asbestos-containing waste material which was
                  deposited at the site during the operating day or
                  previous 24-hour period shall be covered with at least
                  six inches of compacted nonasbestos-containing material.
               b. At the end of each operating day, or at least once every
                  24-hour period while the disposal site is in continuous
                  operation, the asbestos-containing waste material which
                  was deposited at the site during the operating day of the
                  previous 24-hour period shall be covered with a resinous
                  or petroleum-based dust suppression agent which
                  effectively binds dust and controls wind erosion. Such
                  agent shall be used as recommended for the particular
                  dust by the dust suppression agent manufacturer. Other
                  equally effective dust suppression agents may be used
                  upon prior approval by the Air Pollution Control Officer.
                  For purposes of this section, waste crankcase oil is not
                  considered a dust suppression agent.

    311  EXCEPTIONS TO VISIBLE EMISSION STANDARD:
         311.1 Rather than meet the no visible emission requirements as
               specified by Sections 302, 303, 304 or 308, an owner or
               operator may elect to use air cleaning to clean emissions
               containing particulate asbestos material before such
               emissions escape to, or are vented to, the outside air. If
               air cleaning is elected, the following requirements shall
               apply:
               a. Fabric filter collection devices shall be used, except
                  as noted in Subsections 311.1.b, 311.1.c, or 311.d. Such
                  devices shall be operated at a pressure drop of no more
                  than four inches water gage, as measured across the
                  filter fabric. The airflow permeability, as determined
                  by ASTM method D737-69 the test method referenced in
                  Section 501.4, must not exceed 30ft3/min/ft2 for woven
                  fabrics or 35 ft3/min/ft2 for felted fabrics, except that
                  40 ft3/min/ft2 for woven and 45 ft3/min/ft2 for felted
                  fabrics is allowed for filtering air from asbestos ore
                  dryers. Each square yard of felted fabric must weigh at
                  least 14 ounces and be at least one-sixteenth inch thick
                  throughout. Synthetic fabrics must not contain fill yarn
                  other than that which is spun.
               b. If the use of fabric filters creates a fire or explosion
                  hazard, the Air Pollution Control Officer may authorize
                  the use of wet collectors designed to operate with a unit
                  contacting energy of at least 40 inches water gage
                  pressure.
               c. A HEPA filtration system may be used in place of a fabric
                  filter collection device. If a new HEPA filter is used,
                  it shall be certified, by the manufacturer to be at least
                  99.97% efficient for 0.3 micron particles.
               d. The Air Pollution Control Officer may authorize the use
                  of filtering equipment other than that described in
                  Section 311.1, if the owner or operator demonstrates to
                  the satisfaction of the Air Pollution Control Officer
                  that the filtering of particulate asbestos material is
                  equivalent to that of the described equipment.
               e. All air-cleaning equipment authorized by this rule shall
                  be properly installed, used, operated, and maintained.
                  Bypass devices may be used only during upset or emergency
                  conditions and then only for so long as it takes to shut
                  down the operation generating the particulate asbestos
                  material.


400 ADMINISTRATIVE REQUIREMENTS

    401  REPORTING: The owner or operator of any source to which this rule is
         applicable shall provide the following information to the Air
         Pollution Control Officer:
            401.1 For any demolition or renovation, a written plan of
                  intention to demolish or renovate shall be provided to
                  the Air Pollution Control Officer in the following
                  manner:
               a. Delivery of the original plan shall be by the U.S. Postal
                  service, commercial delivery service, or hand delivered
                  by an agent of the owner or operator.
               b. Postmark or delivery of the original plan shall be as
                  follows:
                  1.  At least ten working days prior to commencement of
                      set up for demolition or planned renovation; or
                  2.  At least twenty-four hours prior to commencement of
                      ordered demolition; or
                  3.  As early as possible prior to commencement of
                      emergency renovation.
                  4.  As soon as possible after demolition begins due to
                      burning.
               c. Such plan shall be filed in the manner and form
                  prescribed by the Air Pollution Control Officer,
                  accompanied by the appropriate plan fee, if any. An
                  individual plan shall be submitted for each renovation
                  or demolition area where separate physical barriers are
                  required, pursuant to Section 301.4, and with a separate
                  set up, start, and completion date.
               d. The plan shall include all of the following information:
                  1.  Designation that the plan is the original or a
                      revision.
                  2.  Name, address and telephone numbers of both the
                      owner and the operator of the demolition or
                      renovation.
                  3.  Description of the structure being demolished or
                      renovated, including the size, number of floors, age
                      of the oldest portion, and present and prior use of
                      the structure.
                  4.  Estimate of the approximate amount of RACM to be
                      removed from the structure or portion thereof, in
                      terms of length of pipe in linear feet, surface area
                      in square feet, or volume in cubic feet if the
                      material is not attached to facility components.
                  5.  Estimate of the approximate amount of Category I and
                      Category II nonfriable asbestos-containing material
                      that will not be removed before demolition.
                  6.  The procedure used, including the analytical
                      laboratory method employed, to locate and identify
                      the presence of RACM and Category I and Category II
                      nonfriable asbestos-containing material. A copy of
                      the survey report shall be provided upon request for
                      review by the Air Pollution Control Officer. 
                  7.  Address and location (including building number or
                      name and floor or room number, as applicable) of
                      each structure where demolition or renovation will
                      occur.
                  8.  Scheduled starting date of set up, scheduled
                      starting date of demolition or renovation, and
                      scheduled completion date of demolition or
                      renovation. 
                  9.  Description of planned demolition or renovation and
                      method(s) to be employed.
                  10. Description of work practice and engineering
                      controls to be used including emission control
                      procedures for asbestos removal and waste handling.
                  11. The name and address and location of the waste
                      disposal site where the asbestos-containing waste
                      material will be deposited. 
                  12. A copy of the order to demolish including the name,
                      title, and authority of the state or local
                      governmental representative who has ordered a
                      demolition.
                  13. Certification that at least one person, trained as
                      required by Section 301.10, will supervise the
                      stripping and removing described in this plan.
                  14. Description of the procedures to be followed in the
                      event that unexpected RACM is found or Category II
                      nonfriable asbestos-containing material becomes
                      friable. 
                  15. For emergency renovations described in Section 216,
                      the date and hour that the emergency occurred, a
                      description of the sudden, unexpected event, the
                      name of the person who determined the situation to
                      be an emergency, and an explanation of how the event
                      constitutes an unsafe condition, or would cause
                      equipment damage.
                  16. Name address and telephone number of the waste
                      transporter.
               e. For purposes of determining whether a planned renovation
                  constitutes a renovation within the meaning of this
                  section, the period shall not be less than 30 days and
                  not longer than one year, beginning January 1 and ending
                  December 31.
               f. An emergency renovation shall include only the amount of
                  RACM that must be removed or stripped as a result of the
                  sudden, unexpected event that necessitated the
                  renovation.
               g. No demolition or renovation shall begin or be completed
                  on a date other than the date contained in the written
                  plan, unless the owner or operator submits a written
                  revision. Any revision made to the set up, start, or
                  completion date must be delivered, facsimiled or
                  postmarked to the Air Pollution Control Officer, on or
                  prior to the latest reported corresponding date. Any
                  revision to the set up date shall be postmarked or
                  delivered at least 10 working days before set up work
                  begins. 
               h. Whenever a demolition or renovation, subject to Section
                  301, extends 30 days or more beyond the actual date when
                  set up was first commenced, the owner or operator shall
                  report in writing every 30 days, the following to the Air
                  Pollution Control Officer:
                  1.  The amount of RACM removed as of the time of the
                      report.
                  2.  The amount of RACM remaining to be removed as of the
                      time of the report.
         401.2 A description of the emission control equipment used for each
               process.
         401.3 If a fabric filter device is used to control emissions, the
               pressure drop across the fabric filter in inches water gage.
               a. If the fabric filter device utilizes a woven fabric, the
                  airflow permeability in ft3/min/ft2,and, if the fabric is
                  synthetic, indicate whether the fill yarn is spun or not
                  spun.
               b. If the fabric filter device utilizes a felted fabric, the
                  density in oz/yd2, the minimum thickness in inches, and
                  the air flow permeability in ft3/min/ft2.
         401.4 For waste disposal operations subject to Sections 302 and
               309:
               a. A brief description of each process that generates
                  asbestos-containing waste material;
               b. The average weight of asbestos-containing waste material
                  disposed of, measured in kg/day;
               c. The emission control methods used in all stages of waste
                  disposal;
               d. The type of disposal site or incineration site used for
                  ultimate disposal;
               e. The name of the site operator; and
               f. The name and location of the disposal site.
         401.5 For inactive waste disposal sites subject to Section 310:
               a. A brief description of the site; and
               b. The method or methods used to comply with the standard,
                  or alternative procedures to be used.
         401.6 To obtain approval for a conversion operation pursuant to
               Section 302.3.c, the owner or operator shall provide the Air
               Pollution Control Officer with the following:
               a. An application for Authority to Construct, pursuant to
                  that specified in Regulation 2 of the District Rules and
                  Regulations, and including the following:
                  1.  Description of waste feed handling and temporary
                      storage;
                  2.  Description of process operating conditions;
                  3.  Description of the handling and temporary storage of
                      the end product;
                  4.  Description of the protocol to be followed when
                      analyzing output materials by TEM as described in
                      Section 501.3;
                  5.  A demonstration of the conversion process, upon
                      request of the Air Pollution Control Officer; and
                  6.  A protocol for the start-up performance test and a
                      schedule by which the operating parameters shall be
                      monitored pursuant to Section 501.1.
               b. A report for each analysis of product composite samples
                  performed during the initial 90 days of operation.
               c. A quarterly report, including the following information
                  concerning activities during each consecutive 3 month
                  period:
                  1.  Results of analyses of monthly product composite
                      samples;
                  2.  A description of any deviation from the operating
                      parameters, its duration, and the corrective action;
                  3.  Disposition of any products produced during a period
                      when the operating parameters were outside the range
                      indicative of asbestos-free; and
                  4.  Information on waste disposal activities as required
                      in Section 310.
         401.7 Any owner or operator who intends to spray asbestos-
               containing material for the purpose of insulating or
               fireproofing equipment and machinery, shall report such
               intention to the Air Pollution Control Officer at least 20
               days prior to the commencement of the spraying operation.
               Such report shall include the following information:
               a. Name of owner or operator
               b. Address of owner or operator
               c. Location of spraying operation
               d. Procedures to be followed to meet the requirements of
                  Section 305.
         401.8 The owner or operator of an active waste disposal site
               referenced in Section 310 shall notify the Air Pollution
               Control Officer in writing at least 45 days prior to
               excavating or otherwise disturbing any asbestos-containing
               waste material that has been deposited at a waste disposal
               site and is covered. If the excavation will begin on a date
               other than the one contained in the original notice, notice
               of the new start date shall be provided to the Air Pollution
               Control Officer at least 10 working days before excavation
               begins and in no event shall excavation begin earlier than
               the date specified in the original plan. The notice shall
               include:
               a. Scheduled starting and completion dates;
               b. Reasons for disturbing the waste;
               c. Procedures to be used to control emissions during the
                  excavation, storage, transport, and ultimate disposal of
                  the excavated asbestos-containing waste material;
               d. Location of any temporary storage site and the final
                  disposal site.


500 MONITORING AND RECORDS:

    501  TESTING PROCEDURE
         501.1 CONVERSION FACILITY: To obtain approval for a conversion
               facility referenced in Section 302.3.c of this rule, the
               owner or operator shall:
               a. Conduct a start-up performance test. The test shall
                  include:
                  1.  A detailed description of the types and quantities
                      of nonasbestos material, RACM, and asbestos-
                      containing waste material processed, (e.g. asbestos
                      cement products, friable asbestos insulation,
                      plaster, wood, plastic, wire, etc.) Test feed is to
                      include the full range of materials that will be
                      encountered in actual operation of the process;
                  2.  Results of analyses that document the asbestos
                      content of the wastes processed, using the method
                      specified in Section 501.2.;
                  3.  Results of the analyses, using the TEM method
                      described in Section 501.3, that document that the
                      output materials are free of asbestos. Samples for
                      analysis are to be collected as 8-hour composite
                      samples, beginning with the initial introduction of
                      RACM or asbestos-containing waste material and
                      continuing until the end of the performance test;
                  4.  A description of operating parameters, such as
                      temperatures and residence time, defining the full
                      range over which the process is expected to operate,
                      and the limits for each operating parameter within
                      which the process will produce nonasbestos
                      (asbestos-free) materials; and
                  5.  The length of the test.
               b. During the initial 90 days of operation the owner or
                  operator shall:
                  1.  Monitor and log, according to a schedule approved by
                      the Air Pollution Control Officer, the operating
                      parameters identified during start-up performance
                      tests;
                  2.  Verify that the input materials are as described
                      during start-up performance tests;
                  3.  Collect and analyze samples, taken as 10-day
                      composite samples (200 gram or 7 ounce sample
                      collected every 8 hours of operation) of all output
                      material for the presence of asbestos. The TEM
                      method referenced in Section 501.3 shall be used to
                      analyze the output material for the presence of
                      asbestos;
                  4.  All output material shall be stored on-site until
                      analysis shows the material to be asbestos-free or
                      disposed of as asbestos-containing waste according
                      to Section 302 of this rule.
               c. After the initial 90 days of operation:
                  1.  Continuously monitor and record the operating
                      parameters identified during start-up performance
                      testing and any subsequent performance testing. Any
                      output produced during a period of deviation from
                      the range of established operating conditions shall
                      be:
                      i.   Disposed of as asbestos-containing waste
                           according to Section 302 of this rule; or
                      ii.  Recycled as waste feed during a time when the
                           process is operating within the established
                           range of operating conditions; or
                      iii. Stored temporarily on-site in a leaktight
                           container until analyzed for asbestos content.
                           After being tested, any material that is not
                           asbestos-free shall either be disposed of as
                           asbestos-containing waste material or recycled
                           as waste feed to the process.
                  2.  Collect and analyze monthly composite samples as in
                      section 501.1.b.3 of this rule.
    501.2   ASBESTOS CONTENT - POLARIZED LIGHT MICROSCOPY: Asbestos content
            shall be determined using the method specified in Appendix A,
            Subpart F, 40 CFR Part 763, Section 1, Polarized Light
            Microscopy. If the asbestos content is less than 10 percent,
            verification shall be made using the point counting method
            specified in Appendix A, Subpart F, 40 CFR Part 763, Section
            1.7.2.4, Polarized Light Microscopy, Quantification of Asbestos
            Content.
    501.3   ASBESTOS CONTENT - TEM: When so indicated, asbestos content shall
            be determined using the National Institute of Standards and
            Technology (NIST) approved Transmission Electron Microscopy (TEM)
            method.
    501.4   FABRIC FILTERS: The airflow permeability of fabric filters shall
            be determined by ASTM method D737-69.

    502  RECORD KEEPING: A person subject to this rule shall maintain all
         records required by this rule for two years and make the records
         available for review by the Air Pollution Control Officer upon
         request.
         502.1 FOR ASBESTOS MILLS OR MANUFACTURING OR FABRICATING
               OPERATIONS: Each owner or operator meet the following
               requirements:
               a. Monitor each potential source of asbestos emissions from
                  any part of the mill, manufacturing, or fabricating
                  facility, including air cleaning devices, process
                  equipment, and buildings that house equipment for
                  material processing and handling, at least once each day,
                  during daylight hours, for visible emissions to the
                  outside air during periods of operation. The monitoring
                  shall be visual observation of at least 15 seconds
                  duration per source of emissions, utilizing the procedure
                  specified in EPA Method 9. The certification requirements
                  for Method 9 do not apply. 
               b. Inspect each air cleaning device at least once each week
                  for proper operation and maintenance, including, to the
                  maximum extent possible without dismantling other than
                  opening the device, the presence of tears, holes, and
                  abrasions in filter bags and for dust deposits on the
                  clean side of bags. For air cleaning devices that cannot
                  be inspected weekly, submit a written maintenance plan
                  to the Air Pollution Control Officer including but not
                  limited to the following:
                  1.  Maintenance Schedule;
                  2.  Record keeping plan;
                  3.  Maintenance records of the results of visible
                      emissions monitoring and air cleaning device
                      inspections including the following;
                      i.   Date and time of each inspection;
                      ii.  Presence or absence of visible emissions;
                      iii. Condition of fabric filters, including
                           presence of tears, holes and abrasions;
                      iv.  Presence of dust deposits on clean side of
                           filter;
                      v.   Brief description of corrective actions taken,
                           including date and time; and
                      vi.  Daily hours of operation for each air cleaning
                           device.
                  4.  On a quarterly basis, submit a copy of visible
                      emissions monitoring records if visible emissions
                      occurred during the reporting period. Quarterly
                      reports shall be postmarked by the 30th day
                      following the end of the calendar quarter. 
         502.2 ACTIVE WASTE DISPOSAL SITES: For all asbestos-containing
               waste material received, the owner or operator shall:
               a. Maintain waste shipment records, including the following
                  information:
                  1.  The name, address and telephone number of the waste
                      generator;
                  2.  The name, address and telephone number of the
                      transporter(s);
                  3.  The quantity of the asbestos-containing waste
                      material in cubic yards;
                  4.  The presence of improperly enclosed or uncovered
                      waste, or any asbestos-containing waste material not
                      sealed in leaktight containers. If this condition
                      exists, report in writing to the Air Pollution
                      Control Officer, by the following working day.
                      Submit a copy of the waste shipment record along
                      with the report;
                  5.  The date of receipt.
               b. Send a copy of the signed waste shipment record to the
                  waste generator, as soon as possible, and no longer than
                  30 days after the receipt of the waste;
               c. Upon discovering a discrepancy between the quantity of
                  asbestos-containing waste material noted in the waste
                  shipment records and the quantity actually received,
                  attempt to reconcile the discrepancy with the waste
                  generator. If the discrepancy is not resolved within 15
                  days after receiving the waste, immediately report in
                  writing to the Air Pollution Control Officer. Describe
                  the discrepancy and attempts to resolve it, and a copy
                  of the waste shipment record.
               d. Maintain, until closure, records of the location, depth
                  and area, and the quantity in cubic yards of asbestos-
                  containing waste material within the disposal site on a
                  map or diagram of the disposal area.
               e. Upon closure of the facility, submit a copy of records
                  of asbestos waste disposal locations and quantities.
         502.3 CONVERSION OPERATIONS: The owner or operator shall maintain
               the following records:
               a. Results of the start-up performance testing and all
                  subsequent performance testing, including operating
                  parameters, feed characteristics and analyses of output
                  materials;
               b. Results of the composite analyses required in Section
                  501.1.b.3 and 501.1.c.2;
               c. Results of the continuous monitoring and logs of process
                  operating parameters required in Sections 501.1.b.1 and
                  501.1.c.1;
               d. The waste shipment records including the information
                  required in Section 502.2.a for all asbestos-containing
                  waste received;
               e. The name and location of the purchaser or disposal site
                  and the date of sale or deposit for output materials.